Fitting Ring on uPVC, Composite and Narrow Door Frames

• A drill bit can meet the steel, which makes a clean hole slow and easy to wander
• A cable hole can cross the frame's drainage and weather seals, letting water in where it is meant to drain away
• The face of the frame is often too narrow to take a doorbell's mounting plate square
• Drilling may affect the door installer's warranty, so check it before anything is fixed

• The door slab is not drilled, and the frame is drilled only if you accept the risk to the warranty
• If the door has a standard 12–14 mm viewer and is 32.5–60 mm thick, a Peephole Cam 2K uses the existing hole
• A battery doorbell on the wall beside the door leaves the doorset exactly as it was sold

• Ring's doorbell instructions use a 6 mm masonry bit and the supplied anchors in brick, render or concrete, and no anchors in timber
• Ring's supplied screws are used throughout, as Ring warns that the wrong screws could damage the battery and create a fire hazard
• Render is sounded first, because hollow or cracked render will not hold a fixing; the pro goes through to sound masonry and seals the holes
• A wired doorbell's cable runs through the wall, not the frame, and Ring says its Plug-In Adapter cable can be run through a wall, a door or a window

• Wedge kits tilt the doorbell up or down: on most models, three stackable 5° wedges give up to 15°
• Corner kits turn it sideways: on most models, three 15° pieces give up to 45°. Ring's kits for the Wired Doorbell Pro and Video Doorbell Wired differ, with two 10° wedges or a single 25° corner piece
• A wedge and a corner kit can be combined, but only one kit goes with a Solar Charger or a No-Drill Mount
• Only Ring's supplied screws, 31 mm or shorter, are used with an angle kit
• The Wired Doorbell 2K Plus and 4K Pro and the Battery Doorbell 2K Plus and 4K Pro come with a corner kit in the box

• The door from the path, showing the frame and a good width of wall on each side
• A close-up of the frame where you would like the doorbell, and of any existing bell push
• The door's warranty or installer details, if you have them
• Which Ring doorbell you bought, and for a wired one, the nearest indoor socket

A vetted pro prices your Ring job from the model and your photos, and the JACK app shows that fixed price before you book.

Power moves the price more than the model name. A battery doorbell or camera on a wall with a good signal is the lightest job. A wired doorbell brings in the bell transformer: if yours gives 8–12 V AC and the doorbell needs 16–24 VAC, the job includes fitting Ring's 24 V Plug-In Adapter or a transformer on a fused spur, plus bypassing the old chime. A floodlight cam is priced as electrical work on your outside-light circuit, including any change to how it is switched.

The wall and the height come next: solid brick, render, a narrow uPVC frame that needs a wedge or corner kit, or a camera 2.5–3 m up that needs a ladder or a tower. On a high eave, your pro can ask another pro on JACK to help through the Pro2Pro feature. Cable runs through brick or to a PoE switch add time, and so does each extra device, though every device can go on one booking for one fixed price.

You buy the device; JACK does not sell any. Accessories the job needs, such as a transformer, a Ring Chime, a wedge kit or an outdoor junction box, are agreed and added at cost before you book, and so is parking where it has to be paid for. Prefer to pay for time? As a guide, hourly hire is typically £45–£95 per hour for smart home work and £55–£110 per hour for electrical work. For a big multi-device job, say a doorbell, three cameras and an alarm kit, a full-day handyman booking is a flat £350–£400 for up to 8 hours on site.