Philips Hue · Switches and modules
Philips Hue Wired Wall Switch Module Installation in London
Updated
Hue's wired wall switch module does the same job as its battery module, keeping your Hue lights powered while the wall switch works them through the Hue Bridge, but it runs from the mains and needs a neutral wire. It was temporarily out of stock on Hue's UK store when JACK checked on 1 November 2026, so this page is for people who already have one. A vetted JACK pro in London who does electrical work finds a neutral behind your switch or at the light, fits the module there and pairs it, for a fixed price in the JACK app before you book.
In short
Yes. A vetted JACK pro in London who does electrical work fits the Philips Hue wired wall switch module, which needs a neutral wire, a Hue Bridge and room for a 41 × 37 × 15 mm module, either behind your wall switch or in the ceiling above the light, as Hue allows. Most UK switch boxes have no neutral, so the pro tests both places before deciding. The work alters an existing circuit, which is not notifiable in England outside a bathroom's zones; ask your pro for a Minor Electrical Installation Works Certificate.
Get matched
Start a JACK request
Native app
Start the request here, then add extra photos or videos from the JACK app if the pro needs more detail.
Wired Wall Switch Module: key facts
- UK store status
- 'Temporarily out of stock' in 1- and 2-packs on Hue's UK switches page, 1 November 2026 Source: Philips Hue UK: switches
- Power
- 220–240 V mains; Hue's product description says 'Battery-free, neutral wire required' Source: Philips Hue UK: wired wall switch module for smart lights (1-pack)
- Where it goes
- 'behind your wall switch, or in the ceiling above your light fixture, where a neutral wire is available' Source: Philips Hue UK: wired wall switch module for smart lights (1-pack)
- Class, rating and size
- Class II, IP20, dry locations only, −5 to 45 °C; 41 × 37 × 15 mm Source: Philips Hue UK: wired wall switch module for smart lights (1-pack)
- Connections
- Push-in 5-terminal connector supplied 'to keep mains connected'; solid conductors of 0.75–4 mm², stripped 11 mm Source: Philips Hue UK support: wall switch modules
- Wires it needs
- One or two load wires (one per button), a neutral and two line wires Source: Philips Hue UK support: wall switch modules
- Switches
- Rocker or push, with a single or dual button Source: Philips Hue UK: wired wall switch module for smart lights (1-pack)
- Radios and Bridge
- Zigbee, acting as a repeater, and Bluetooth; Hue Bridge required, with Matter through the Bridge Source: Philips Hue UK: wired wall switch module for smart lights (1-pack)
- Bridge support
- Hue's Bridge release notes of 2 July 2026 added support for 'Wired Wall Switches and Modules' Source: Philips Hue: Bridge release notes
Product facts come from Philips Hue's UK product pages and support articles, linked beside each fact; where the UK page is silent, a few come from Hue's other English-language sites and say so. Hue changes its range often, so check the model on your box or order and send it with your request. Last checked 1 November 2026.
How the Wired Wall Switch Module is powered and mounted
Where the battery module runs on a coin cell, this one takes power from the circuit, which is why Hue's product description calls it battery-free and asks for a neutral. The result for the lights is the same: they stay powered, and a press of the wall switch becomes a command through the Hue Bridge rather than a cut in the supply. Being always on, it also repeats the Zigbee signal. One answer further down the same Hue page says it runs on batteries; the 220–240 V rating, the neutral requirement and Hue's support article all describe a mains device, and the pro treats it as one.
The neutral is the sticking point in British homes. A loop-in lighting circuit brings the permanent live, the neutral and the switched live together at the ceiling rose and sends only the live and the switched live down to the switch, so most UK switch boxes have no neutral to give. Hue's own wording leaves room for that: the module may go in the ceiling above the light instead. In a London house with ordinary loop-in wiring that often means the rose or the void just above it, where Hue's wall switch finder warns that in older UK installations the neutral 'may be black'.
Up in the ceiling, the module still needs space, and its rating sets limits. Hue rates it for dry locations from −5 to 45 °C, so JACK does not fit it inside a bathroom or an outside light, and in the ceiling it sits clear of the fitting's heat. Where no neutral is reachable at all, a new cable can be run from the rose down to the switch; that is an alteration to the existing circuit rather than a new one, but it means chasing the wall and making good, priced before you book.
What the pro checks first
- Where a neutral is available, tested at the switch, the ceiling rose or a junction box rather than guessed from wire colours
- Whether the switch is a rotary dimmer or shares a plate with a socket, neither of which Hue supports
- The cable size in the box, since Hue's connector is specified for solid conductors of 0.75–4 mm²
- Space for the module behind the switch or in the rose without crowding the other connections
- That the lights on the circuit are Hue and a Hue Bridge is already running
What the pro does on the Wired Wall Switch Module
- Circuit isolated at the consumer unit, proved dead and the neutral identified by test
- Line, neutral and load wired through Hue's 5-terminal connector, each conductor stripped to the 11 mm Hue specifies
- Where the module goes in the ceiling, it is seated in or above the rose, clear of the lamp's heat
- On a two-gang switch, a load wire for each button, so each one runs its own group of Hue lights
- Module paired to the Bridge and its buttons set as rocker or push
- Circuit tested once the module is in; ask your pro for a Minor Electrical Installation Works Certificate covering the change
How the Wired Wall Switch Module installation goes
- 1Photos of the switch, the light and any ceiling rose reviewed, so the likeliest neutral position is known before the visit
- 2Module added in the Hue app on your Bridge
- 3Supply switched off at the consumer unit and checked dead with a tester
- 4Neutral found and tested at the switch or the rose, then the module wired in
- 5Switch plate or rose cover refitted, power restored and every button tried
- 6Button actions and rooms set in the Hue app with you
Before you book: what to send
- A photo of the switch with its plate on, and one of the light it controls
- If the light hangs from a ceiling rose, a photo of the rose from below
- Which Hue lights are on the circuit, and whether your Hue Bridge or Bridge Pro is running
- That you already have the module, since it was out of stock on Hue's UK store on 1 November 2026 and JACK does not sell Hue devices
- Whether a new cable chased down to the switch is acceptable if no neutral can be reached
What if there is no neutral at your switch?
That is the usual case in a UK home, and there are four ways round it, from the least disruptive:
- Fit the wired module at the ceiling rose or in the void above the light, the alternative Hue gives on its own product page
- Use Hue's battery wall switch module behind the switch instead, since it needs no neutral
- Run a new cable with a neutral from the rose to the switch, an alteration to the existing circuit that is not notifiable but leaves a wall to make good
- Keep the switch on and use a battery Hue remote beside it, which needs no wiring but can still be switched off by mistake
Where can the Hue wired wall switch module go in a London home?
It goes wherever a neutral, the lighting circuit and enough room for the module meet:
| Position | Neutral there? | What the job involves |
|---|---|---|
| Behind the switch, loop-in wiring | Usually not | Module placed elsewhere, or a new cable with a neutral run down from the rose |
| Ceiling rose above the light | Usually, on loop-in circuits | Module in or just above the rose, the ceiling option Hue offers |
| Junction box in the ceiling void | Usually, where the circuit is joined there | Reached through the light's opening or from a loft hatch above |
| Behind the switch, newer wiring | Sometimes, where an installer brought a neutral down | Module in the back box, if it is deep enough |
| Bathroom, or an outside light | Not relevant | Not booked: Hue rates the module for dry locations, and JACK does not book fixed work in bathroom zones |
Wire colours are not proof on their own: Hue's wall switch finder says the neutral may be black in older UK wiring, so the pro tests before connecting anything.
How is Philips Hue installation priced in London?
A vetted pro prices your Hue job from the products and your photos, and the JACK app shows that fixed price before you book.
Full pricing guide for Philips Hue installationFrequently asked questions
Does the Philips Hue wired wall switch module need a neutral wire?
Yes. Hue's product page says 'neutral wire required' and its support article lists a neutral among the wires it needs. Because most UK switch boxes have none, Hue also allows it to go in the ceiling above the light, and that is where many London fits end up.
Is the Hue wired wall switch module battery-powered?
No. Hue's product description says 'Battery-free', although one answer lower on the same page says it runs on batteries. The description, the 220–240 V rating and the neutral it needs all point to a mains-powered module, so there is no coin cell to replace.
Who can fit a Hue wired wall switch module in London?
A competent pro who does electrical work, because in England fitting it to an existing lighting circuit outside a bathroom's zones is not notifiable under Part P. Hue's page warns that fitting it means handling live mains wires and tells you to check local regulations; ask your pro for a Minor Electrical Installation Works Certificate. A new circuit, or anything in a bathroom zone, needs a registered electrician, which JACK does not book.
How much does Philips Hue Wired Wall Switch Module installation cost in London?
It is a fixed price for your Wired Wall Switch Module, worked out by a vetted pro from the model, a photo of where it is going and what power is there now, and shown in the JACK app before you book. Other devices can go on the same booking for one price. If you would rather pay for time, hourly hire for electrical work is typically £55–£110 per hour as a guide.
Often booked together
Wall Switch Module installation
Hue's battery module (CR2450) for the back box behind your existing switch: no neutral needed, so it suits most UK switch boxes, and your Hue lights stay reachable.
Wired Modules for Non-Smart Lights installation
Hue's in-wall on/off switch (1- or 2-channel) and dimmer for ordinary lights: your fittings stay, and the module behind the switch makes them work with Hue.
Bridge Pro installation
Hue's top hub, listed for 150 lights and 50 accessories: placed and cabled to the router, an older Bridge migrated across, and everything the move drops put back.
More Philips Hue switches and modules
Philips Hue switch and wall switch module installation
Hue's battery and wired wall switch modules, wired switches for ordinary lights and Hue remotes, matched to the wiring at your switch.
All Philips Hue installation guides
Philips Hue installation in London: ceiling lights, downlights, wall switch modules, outdoor lights and Secure cameras fitted by vetted pros. Fixed price first.
Related services in London
Electrical Work
Fault finding, lights, sockets, switches, and small electrical jobs.
Smart Home
Smart locks, cameras, doorbells, thermostats, Wi-Fi, and setup help.
Electrical Fault Finding
Fault finding and repairs by vetted London electricians, often same day — tripping fuse boards, dead sockets, flickering lights.
Sources
The device facts and rules on this page come from these pages, checked on 1 November 2026.
Jack All Trades (JACK) is an independent London service. It is not part of, affiliated with or endorsed by Signify, which makes Philips Hue and uses the Philips brand under licence, or by Philips. Philips Hue product names are used only to describe the products JACK pros fit and set up; prices are set by JACK pros, not by Signify, and JACK does not sell Hue products.
Get your Philips Hue fitted
List your Hue products in the JACK app with photos of the lights, switches and walls involved. A vetted pro prices the whole job up front, and you pick a time that suits you.
Get a fixed price in the app