tado° · Receivers and hot water
tado° Wireless Smart Thermostat V3+ Installation in London
Updated
The tado° Wireless Smart Thermostat Starter Kit V3+ with Hot Water Control is the older tado° wireless kit: a UK receiver that replaces a heating and hot water programmer, a battery sensor and an Internet Bridge at your router. tado°'s UK shop still listed it on 31 October 2026. A vetted JACK pro fits or extends it in London for a fixed price before you book.
In short
Yes. A vetted JACK pro in London fits the tado° Wireless Smart Thermostat V3+ kit: the UK receiver replaces your two-channel programmer on the existing wiring for an S-plan, Y-plan or combi relay system, the Internet Bridge goes on your router, and the sensor goes where it reads the room. The V3+ UK receiver works by relay only, with no OpenTherm.
Get matched
Start a JACK request
Native app
Start the request here, then add extra photos or videos from the JACK app if the pro needs more detail.
Wireless Smart Thermostat V3+: key facts
- Full UK name
- Wireless Smart Thermostat Starter Kit V3+ with Hot Water Control (also a Black Edition) Source: tado° UK shop: all products
- In the box
- Wireless Receiver (BP02), Wireless Temperature Sensor (SU02) and Internet Bridge (IB01) Source: tado° help: starter kits and model codes
- Wiring
- Relay only: S-plan, Y-plan, and combi with volt-free or switched live contacts Source: tado° V3+ UK installer manual: Wireless Smart Thermostat with hot water control
- Internet Bridge
- Plugs into the router by Ethernet and takes power from the router's USB port or its own 5 V adapter Source: tado° V3+ UK installer manual: Wireless Smart Thermostat with hot water control
- Compatibility
- Works only with other tado° V3+ devices; cannot share a Home with tado° X Source: tado° help: tado° X and other tado° product lines
Model details come from tado°'s UK shop, help centre and installer manuals. tado° can change a design or what comes in the box, so check your own kit and send a photo of it with your request. Last checked 31 October 2026.
How the Wireless Smart Thermostat V3+ is powered and mounted
The V3+ receiver does the same job as the newer X receiver, replacing a two-channel programmer so heating and hot water run on their own schedules, but tado°'s UK manual shows relay wiring only. It has no OpenTherm, so a combi runs on or off rather than modulating.
V3+ talks to the internet through the Internet Bridge, which plugs into a spare router port by cable. It cannot be swapped for a Bridge X, and V3+ homes add V3+ radiator thermostats and sensors rather than X devices.
What the pro checks first
- The programmer it replaces, and how its wires are connected
- S-plan, Y-plan or combi relay, as the V3+ receiver has no OpenTherm
- A free Ethernet port on the router for the Internet Bridge
- The cylinder label: vented or unvented
What the pro does on the Wireless Smart Thermostat V3+
- Old programmer removed with the heating supply isolated, and the receiver wired on the existing cables
- Set for S-plan, Y-plan or combi relay to match the system
- Internet Bridge cabled to a spare router port and powered
- Sensor placed on an inside wall or stand and paired
- Heating and hot water tested from the app
Before you book: what to send
- A photo of the programmer the receiver replaces
- Whether you have a hot water cylinder, and its label
- A free Ethernet port on your router, and whether it has a USB socket
How tado° installation is priced
A vetted pro prices your job from photos of the boiler, your existing controls and the tado° kit, and the JACK app shows you that fixed price before you book.
Full pricing guide for tado° installationFrequently asked questions
Should I fit V3+ or buy tado° X instead?
If you already have V3+ devices, V3+ keeps everything in one Home. tado° X needs a new Home and cannot use V3+ devices, but its UK receiver adds OpenTherm. Neither is wrong; it depends on what you own already.
Can the V3+ receiver go straight onto my boiler?
Where there is an existing programmer, the receiver goes in its place. Wiring at the boiler's own terminals, for a boiler with no external controls, needs a Gas Safe engineer and is not part of a JACK booking.
How much does tado° Wireless Smart Thermostat V3+ installation cost in London?
It is a fixed price for your Wireless Smart Thermostat V3+, worked out by a vetted pro from the model, a photo of where it is going and what power is there now, and shown in the JACK app before you book. Other devices can go on the same booking for one price. If you would rather pay for time, hourly hire for smart home is typically £45–£95 per hour as a guide.
Often booked together
Smart Radiator Thermostat V3+ installation
V3+ radiator heads (VA02), including the Basic, added to an existing V3+ system.
Wired Smart Thermostat V3+ installation
The V3+ wired thermostat (RU02): refitted on its cable, or swapped when you move to X.
Wireless Receiver X installation
The UK receiver (PR04), also sold as Programmer X: replaces a programmer, controls hot water.
More tado° receivers and hot water
tado° receiver and hot water installation
UK receivers that replace a programmer: combi, S-plan, Y-plan and gravity-fed hot water.
All tado° installation guides
tado° Smart Thermostat X, Wireless Receiver X and radiator thermostats fitted in London by vetted pros who work at the wall, not the boiler. Fixed price first.
Related services in London
Sources
The device facts and rules on this page come from these pages, checked on 31 October 2026.
Jack All Trades (JACK) is an independent London service. It is not part of, affiliated with or endorsed by tado GmbH. tado° product names are used only to describe the devices JACK pros install, and prices are set by JACK pros, not by tado°. JACK pros do not work inside boilers or claim Gas Safe registration.
Get your tado° heating fitted
Send photos of your boiler, your current controls and your tado° kit in the JACK app, see a fixed price from a vetted local pro, and pick a time that suits you.
Get a fixed price in the app